Thick film hybrid

The advantages of Hybrid Microcircuits over PCB technology

Reduced Size

Hybrids usually contain un-packaged semiconductors which are typically <10% of the volume of the packaged devices used on PCB assemblies. Resistors are laser-trimmed printed ink squares on the tracklayer instead of discrete components used on PCB assemblies.

Hybrids are not low-cost PCB assemblies, they are however comparable in cost when all the constraints of PCB technology are considered.

Inherent thermal management

Substrates are commonly Alumina which is a highly thermally conductive material that transfers heat away from hot-spots quickly and efficiently, dissipating it over the whole surface. PCB material is commonly epoxy based with poor thermal conductivity, leading to hot-spots which reduce the life of most semiconductor junctions.

RoHS

RoHS does not apply to parts internal to a device, only to external packaging and terminations. Hybrid microcircuits contain palladium silver terminated devices attached with conductive adhesive and bare silicon die which are wire bonded with no RoHS implications. Hybrids do not need to be XRF tested unlike PCB assemblies used in some critical applications.

Hybrid microcircuits are inherently more reliable than PCB assemblies.

Tin whiskers

The tin whisker phenomena is real, tangible and well documented. Ultra Electronics, CEMS has seen examples of whiskers from <1mm long growing between components on PCBs to 15mm long whiskers on the exterior of a metal enclosure. Whiskers occur most often in the context of lead-free RoHS compliant solder terminations. However, hybrids predominantly use un-packaged bare die semiconductors which are connected using wire bonding and other discrete components. These in turn, are connected using conductive adhesive instead of solder. Tin whiskers do not grow within a hybrid.

Qualification to MIL spec as single part

In the context of MIL PRF, the hybrid microcircuit is regarded as a single component regardless of the number of devices held within it. Therefore, a single hybrid microcircuit containing any number of parts can be qualified in a single process. This compares with a PCB assembly where multiple components may require individual qualification for a specified configuration.

Hybrid microcircuits are inherently more secure than PCB assemblies.

ESS robustness

Hybrids are microelectronic circuits comprising multiple devices, often unpackaged, within a hermetically sealed metal enclosure or an impervious conformal coating. All components are insulated and isolated to a high level, giving constituent parts protection from moisture ingress. Hybrid substrates have their conductive tracking and insulating layers fired at 850°C for one hour, with conductive adhesive device terminations being cured at 150°C for two hours. By comparison, FR4 PCB assemblies face a maximum temperature of approximately 80 - 100°C for short periods, beyond which damage to the PCB structure starts to occur.

Hybrids are 'game changers' in terms of the functionality that can be achieved within a given space and weight.

High temperature

Hybrids utilise components which are increasingly capable of long term operation at up to 200°C. The component industry is now moving toward 250°C operation. Ultra Electronics, CEMS is building on early experience of hybrid design designing and fabricating high temperature hybrids. By using these emerging parts, that capability is further extended.

Active trimming of resistors

Resistor values can be adjusted by way of laser trimming during the functional operation of the circuit, allowing the dynamic tuning of circuits as an automated production process.

Reduced PCB complexity

Digital devices typically have a high number of interconnections and they can usually be obtained in bare die format suitable for hybridisation. The inclusion of analogue parts within the hybrid results in most interconnections being inside the hybrid design. This reduces the number of external or PCB mounted interconnections and allows the PCB upon which the hybrid is mounted to be less complex: fewer layers, fewer parts and fewer fine-line tracks, gaps and via holes.

Security

Bare die devices are extremely difficult to reverse engineer, as there is no possibility of incremental serialisation or unique ID, thus allowing software detection of non-uniquely identified clones and ensuring a high level of IP protection. Hybrids are commonly sealed with welded metal enclosures or high integrity conformal coatings, making it difficult to discover the identity of integral devices compared with the equivalent PCB assemblies.

Single tested component

A hybrid may contain a thousand devices but when it is received by the customer it is one device which has been tested thoroughly to the agreed specification.

Higher reliability

By using bare die within a hybrid the total number of interconnections is reduced significantly as is the resultant number of solder joints on the host PCB, increasing the fundamental reliability of the circuit. Discrete devices within a hybrid are terminated with conductive adhesive, a highly reliable technology not considered to degrade reliability as in the case of solder joints on a PCB.

Corrosion free

Metal hybrid enclosures are typically plated with nickel under gold and internal conductor layers formed with noble metals, removing the risk of corrosion in both cases.

Simplified PCBs

As most interconnections are contained within the hybrid, the number of external connections is substantially reduced, resulting in less complex and lower cost host PCBs.

Uprated devices

Lower cost and widely available instrument grade commercial die can be screened and released to MIL spec as part of the hybrid fabrication process.

Availability of die

Not all silicon is available in bare die form, which may affect the partitioning of the electronic circuit and how it is split between hybrid and host PCB. Parts assigned to the host PCB are necessarily packaged devices which reduce the overall miniaturisation of the circuit. Some die may only be obtained subject to a minimum order quantity, the surplus die having to be stored in nitrogen storage in order to be useable in future.

Long term nitrogen storage

CEMS offers dual redundant nitrogen storage facilities split between two sites.

Thick Film Hybrid Microcircuits Services

Hybrid microelectronics, PCB, mechatronics and system assembly, in-house parylene coating and long term nitrogen storage.

  • Hybrid microcircuit design
  • Thick film hybrid microcircuits
  • Power electronics
  • Sensor electronics
  • Microwave electronics
  • Chip on board
  • Mixed technology hybrid microcircuits
  • Opto-electronic microcircuits
  • Sub-assembly
  • Electronic design
  • Software design
  • Product miniaturisation
Thick Film Hybrids image 1 Thick Film Hybrids image 2 Thick Film Hybrids image 3

Product Miniaturisation in the UK

Find out more

Talk to our Experienced Sales Team

Contact us

Access Reports in our Secure Customer Portal

Log In

Download the details CEMS brochure (1.6MB)

Download now